您要查找的是不是：
- Keywords large gear shaft;austempering;quenching distortion; 大齿轮轴;等温淬火;淬火畸变;
- Keywords large gear;butt slrap face;heat expansion;wedge gash gate;parallel gash gate;fraising screw bolt flange;boom.; 大齿轮;对接面;热胀;楔形张口;平行张口;铰孔螺栓法兰;悬臂杆;
- Keywords Large gear;On-machine measurement;Straight generatrix deviation;Rack-shaped-edge probe; 大齿轮;在机测量;直母线偏差;刃边齿条测头;
- large gear shaft 大齿轮轴
- This large gear turns the small one. 这个大齿轮带动那个小齿轮。
- This large gear turns the small one to rotate the cylinder. 这个大齿轮带动小齿轮使滚筒旋转。
- It is studied the existing three kinds of bearing arrangement for the driving gear shaft of locomotive motor. 摘要研究了现有的3种机车电机主动齿轮轴轴承布置方式。
- The transmission is then moved toward the rear until the main gear shaft clears the clutch disk. It can then be lowered to the floor. 然后,把变速器主传动轴的端部从离合器中抽出,可将其放到地面上。
- The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法，分析了人字齿轮轴发生劈裂的原因。
- The numerical result showed that the length of the extended end of gear shaft has an evidential effect upon speed of losing stability of the system. 数值结果表明，齿轮轴外伸端长度对轴承的负荷分配和系统的临界转速影响十分明显，而对系统的失稳转速则影响较小。
- The remedial maintenance method for broken gear shaft of small or medium equpment is introduced.The usual using can be essured after repaired. 介绍了中小型设备齿轮轴折断的修复方法。通过装配焊接的方式修复，可保证该轴正常使用。
- Highly evaluated by customers as medium and large gear testing machine for their high righty,accurcy and performance. 具有高刚性;高精度;高性能的中;大型齿轮测试机;且在实际使用中得到了用户的认可.
- Abstract The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要 采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法，分析了人字齿轮轴发生劈裂的原因。
- Spinner mainly consisted by cabinet、wedge-shaped sheath、friction wheel、air tube clutch、gear wheel 1、gear wheel 2、gear shaft、motor pinion、air motor and other parts. 旋扣器主要有箱体、楔形套、摩擦轮、气胎离合器、轴出轴套、大齿轮1、大齿轮2、齿轮轴、马达小齿轮、气马达、继气器、箱体底盖、等组成。
- The paper presentcd mill large gear junction place loosened two forms,reasons,measure treatment and structural improving plan. 本文提出磨机大齿轮张口两种表现形式，原因，宜采取的措施及结构改进方案。
- The cold extruding process is one of the most economical and high efficiency technology for the gear shaft with involute-gear-tooth for transferring torque in automobile. 对于传递扭矩的渐开线齿形花键轴,采用冷挤压成形加工方法对其齿形部分进行近净成形加工是高效而经济的。
- The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies. 在具有斜下向孔或斜下向凹凸铸件压铸模设计中,斜下向抽芯是压铸模设计的难点之一。
- Positive displacement main oil pump, mounted on bull gear shaft, oversize and arranged to protect the machine during coast down in the event of a power failure. 安装在大齿轮轴上的主油泵，超尺寸配置，以保护在突然停电时压缩机的充分润滑。
- Keywords dynamic frequency doubler programmable large gear test; 动态倍频器;可编程;大齿轮测量;
- Keywords Large intestine;Schistosomiasis;Autoscope; 大肠;血吸虫;内镜;
